Proxim ORiNOCO AP-700 Bedienungsanleitung

ORiNOCO AP-700 Access PointUser Guide

Introduction AP-700 User GuideGuidelines for Roaming10Figure 1-1 Typical Wireless Network Access InfrastructureGuidelines for Roaming• Typical voice n

Advanced Configuration AP-700 User GuideRadius Profiles100• Destination Port: Enter the port number which the AP and the server will use to communicat

Advanced Configuration AP-700 User GuideRadius Profiles101NOTE: This feature requires RADIUS authentication using MAC Access Control or 802.1x. Wirele

Advanced Configuration AP-700 User GuideRadius Profiles102– Number of octets (bytes) received by subscriber.• Acct-Output-Octets– Number of octets (by

Advanced Configuration AP-700 User GuideSSID/VLAN/Security103SSID/VLAN/SecurityThe AP provides several security features to protect your network from

Advanced Configuration AP-700 User GuideSSID/VLAN/Security104Figure 4-36 Components of a Typical VLANVLAN Workgroups and Traffic ManagementAccess Poin

Advanced Configuration AP-700 User GuideSSID/VLAN/Security105Typical User VLAN ConfigurationsVLANs segment network traffic into workgroups, which enab

Advanced Configuration AP-700 User GuideSSID/VLAN/Security1063. Place a check mark in the Enable VLAN Tagging box.Provide Access to a Wireless Host in

Advanced Configuration AP-700 User GuideSSID/VLAN/Security107• EAP-Tunneled Transport Layer Security (TTLS): Certificate-based authentication (a certi

Advanced Configuration AP-700 User GuideSSID/VLAN/Security108WPA is a replacement for Wired Equivalent Privacy (WEP), the encryption technique specifi

Advanced Configuration AP-700 User GuideSSID/VLAN/Security109VLANs and Security ProfilesThe AP-700 allows you to segment wireless networks into multip

Introduction AP-700 User GuideManagement and Monitoring Capabilities11802.11 direct sequence devices (that operate at 1 or 2 Mbits/sec). Available Fre

Advanced Configuration AP-700 User GuideSSID/VLAN/Security1103. Configure one or more types of wireless stations (security modes) that are allowed acc

Advanced Configuration AP-700 User GuideSSID/VLAN/Security111• Cipher: CCMP based on AES• PSK Passphrase: an 8-63 character user-defined phrase. It is

Advanced Configuration AP-700 User GuideSSID/VLAN/Security112Figure 4-40 Security Profile Table - Add Entries

Advanced Configuration AP-700 User GuideSSID/VLAN/Security113MAC AccessThe MAC Access sub-tab allows you to build a list of stations, identified by th

Advanced Configuration AP-700 User GuideSSID/VLAN/Security114the same system separated per VLAN. See the Security Profile section for more information

Advanced Configuration AP-700 User GuideSSID/VLAN/Security1156. Enter the Security Profile used by the VLAN in the Security Profile field. See the Sec

Advanced Configuration AP-700 User GuideSSID/VLAN/Security11611. Specify a QoS profile. See the Enabling QoS and Adding QoS policies section for more

Advanced Configuration AP-700 User GuideSSID/VLAN/Security117 Figure 4-45 SSID/VLAN Edit Entries Screen (VLAN Tagging Enabled)4. Enter a unique Networ

Advanced Configuration AP-700 User GuideSSID/VLAN/Security1187. Enable or disable RADIUS accounting on the VLAN/SSID under the Accounting Status drop-

119AP-700 User Guide5MonitoringThis chapter discusses the following monitoring options:• Version: Provides version information for the Access Point’s

Introduction AP-700 User GuideManagement and Monitoring Capabilities12SNMP ManagementIn addition to the HTTP and the CLI interfaces, you can also mana

Monitoring AP-700 User GuideVersion120VersionFrom the HTTP interface, click the Monitor button and select the Version tab. The list displayed provides

Monitoring AP-700 User GuideICMP121ICMPThis tab provides statistical information for both received and transmitted messages directed to the AP. Not al

Monitoring AP-700 User GuideLearn Table122Learn TableThis tab displays information relating to network bridging. It reports the MAC address for each n

Monitoring AP-700 User GuideRADIUS123RADIUSThis tab provides RADIUS authentication, EAP/802.1x authentication, and accounting information for both the

Monitoring AP-700 User GuideInterfaces124InterfacesThis tab displays statistics for the Ethernet and wireless interfaces. Figure 5-8 Interface Monitor

Monitoring AP-700 User GuideInterfaces125• Duplicate Frame Count (Wireless): The number of duplicate frames received.• Ethernet Chipset (Ethernet): I

Monitoring AP-700 User GuideInterfaces126• Out Discards (Ethernet/Wireless): The number of error-free outbound packets chosen to be discarded to preve

Monitoring AP-700 User GuideStation Statistics127Station StatisticsThis tab displays information on wireless clients attached to the AP and on Wireles

Monitoring AP-700 User GuideStation Statistics128• Number of Clients: The number of stations and WDS links monitored.The following stations statistics

129AP-700 User Guide6CommandsThis chapter contains information on the following Command functions:• Introduction to File Transfer via TFTP or HTTP: De

Introduction AP-700 User GuideManagement and Monitoring Capabilities13The SSH server (AP) has host keys - a pair of asymmetric keys - a private key th

Commands AP-700 User GuideIntroduction to File Transfer via TFTP or HTTP130• Uploading files (Configuration, CLI Batch File) from the AP is called “Re

Commands AP-700 User GuideUpdate AP131Update APUpdate AP via TFTPUse the Update AP via TFTP tab to download Configuration, AP Image, Bootloader files,

Commands AP-700 User GuideUpdate AP via HTTP132– CLI Batch File: a CLI Batch file that contains CLI commands to configure the AP. This file will be ex

Commands AP-700 User GuideRetrieve File133A warning message gets displayed that advises the user that a reboot of the device will be required for chan

Commands AP-700 User GuideRetrieve File134– Double-click the TFTP server icon on your desktop and locate the IP address assigned to the TFTP server.•

Commands AP-700 User GuideRetrieve File135Click on the Retrieve File button to initiate the operation. Figure 6-8 Retrieve File via HTTP Command Scree

Commands AP-700 User GuideReboot136On clicking the Save button the Save As window displays, where the user is prompted to choose the filename and loca

Commands AP-700 User GuideHelp Link137Help LinkUse the Help tab to configure the location of the AP Help files.During initialization, the AP on-line h

138AP-700 User Guide7TroubleshootingThis chapter provides information on the following:• Troubleshooting Concepts• Symptoms and Solutions• Recovery Pr

Troubleshooting AP-700 User GuideSymptoms and Solutions139Serial Link Does Not Work1. Make sure you are using a standard, straight-through, 9-pin seri

14AP-700 User Guide2Installation and InitializationThis chapter contains information on the following:• AP-700 Hardware Description– Overview– Antenna

Troubleshooting AP-700 User GuideSymptoms and Solutions1406. Perform the Reset to Factory Default Procedure in this guide. This will reset the unit to

Troubleshooting AP-700 User GuideSymptoms and Solutions141Client PC Card Does Not Work1. Make sure you are using the latest PC Card driver software. 2

Troubleshooting AP-700 User GuideRecovery Procedures1424. Try using a different Ethernet cable – if it works, there is probably a faulty connection ov

Troubleshooting AP-700 User GuideRecovery Procedures1431. While the unit is running, press the RESET button.NOTE: You need to use a pin or the end of

Troubleshooting AP-700 User GuideRecovery Procedures14411.Click OK when prompted that the device has been updated successfully to return to the Scan L

Troubleshooting AP-700 User GuideRecovery Procedures145[Device name]> show[Device name]> set ipaddrtype static[Device name]> set ipaddr 10.0.

Troubleshooting AP-700 User GuideRelated Applications146[Device name]> Please enter password:4. Enter the CLI password (default is public). The ter

Troubleshooting AP-700 User GuideRelated Applications147If a TFTP server is not configured and running, you will not be able to download and upload im

148AP-700 User GuideACommand Line Interface (CLI)This section discusses the following:• General Notes• Command Line Interface (CLI) Variations• CLI Co

Command Line Interface (CLI) AP-700 User GuideGeneral Notes149• Download vs. Upload - Downloads transfer files to the Access Point. Uploads transfer f

Installation and Initialization AP-700 User GuideAP-700 Hardware Description15Figure 2-1 Rear PanelThe AP-700 has been designed to rest horizontally o

Command Line Interface (CLI) AP-700 User GuideCommand Line Interface (CLI) Variations150Command Line Interface (CLI) VariationsAdministrators use the

Command Line Interface (CLI) AP-700 User GuideCLI Command Types151Figure A-2 Results of “show” bootloader CLI commandCLI Command TypesThis guide divid

Command Line Interface (CLI) AP-700 User GuideCLI Command Types152[Device-Name]>?Figure A-3 Result of “?” CLI commandExample 2. Display specific Co

Command Line Interface (CLI) AP-700 User GuideCLI Command Types153Example 3b. Display parameters based on letter sequenceThis example shows entries fo

Command Line Interface (CLI) AP-700 User GuideCLI Command Types154Example:[Device-Name]>download 192.168.1.100 APImage2 img2. Syntax to display hel

Command Line Interface (CLI) AP-700 User GuideCLI Command Types155reboot Reboots Access Point after specified number of seconds. Specify a value of 0

Command Line Interface (CLI) AP-700 User GuideCLI Command Types156Syntax:[Device-Name]>show <parameter>[Device-Name]>show <group>[De

Command Line Interface (CLI) AP-700 User GuideCLI Command Types157Example 1 - Set the Access Point IP Address ParameterSyntax:[Device-Name]>set <

Command Line Interface (CLI) AP-700 User GuideCLI Command Types158Example 5 - Show the Group ParametersThis example illustrates how to view all elemen

Command Line Interface (CLI) AP-700 User GuideUsing Tables and Strings159Using Tables and StringsWorking with TablesEach table element (or parameter)

Installation and Initialization AP-700 User GuideAP-700 Hardware Description16vertically polarized internal antenna, and connector 2 corresponds to th

Command Line Interface (CLI) AP-700 User GuideConfiguring the AP using CLI commands160The string delimiter does not have to be used for every string o

Command Line Interface (CLI) AP-700 User GuideSet Basic Configuration Parameters using CLI Commands161• Download an AP Configuration File from your TF

Command Line Interface (CLI) AP-700 User GuideSet Basic Configuration Parameters using CLI Commands162Figure A-13 Results of “show wif” CLI command fo

Command Line Interface (CLI) AP-700 User GuideSet Basic Configuration Parameters using CLI Commands163Enable and Configure TX Power Control for the Wi

Command Line Interface (CLI) AP-700 User GuideOther Network Settings164Example:[Device-Name]>set wifssidtbl 3.1 ssid accesspt1 vlanid 22 ssidauth e

Command Line Interface (CLI) AP-700 User GuideOther Network Settings165• Configure the AP as a DHCP Server• Configure the DNS Client• Configure DHCP R

Command Line Interface (CLI) AP-700 User GuideOther Network Settings166Configure DHCP RelayPerform the following command to enable or disable DHCP Rel

Command Line Interface (CLI) AP-700 User GuideOther Network Settings167Shutdown/Resume Wireless Service[Device-Name]>set wif <index> wssstatu

Command Line Interface (CLI) AP-700 User GuideOther Network Settings168Set Ethernet Speed and Transmission Mode[Device-Name]>set etherspeed <val

Command Line Interface (CLI) AP-700 User GuideOther Network Settings169Configure Secure Socket Layer (HTTPS)Enabling SSL and configuring a passphrase

Installation and Initialization AP-700 User GuidePrerequisites17 The LED indicators exhibit the following behavior:PrerequisitesBefore installing an A

Command Line Interface (CLI) AP-700 User GuideOther Network Settings170Configure Intra BSS[Device-Name]>set intrabssoptype <passthru (default)/b

Command Line Interface (CLI) AP-700 User GuideOther Network Settings171[Device-Name]set radiustbl 1.2 profname "MAC Authentication" seraddrf

Command Line Interface (CLI) AP-700 User GuideOther Network Settings172Set Rogue Scan ParametersPerform the following command to enable or disable Rog

Command Line Interface (CLI) AP-700 User GuideCLI Monitoring Parameters173Set Security Profile ParametersConfigure a Security Profile with Non Secure

Command Line Interface (CLI) AP-700 User GuideParameter Tables174• statiapp: Displays the IAPP statistics.• statradius: Displays the RADIUS Authentica

Command Line Interface (CLI) AP-700 User GuideParameter Tables175– IP Access Table Parameters - Configure range of IP addresses that can access the AP

Command Line Interface (CLI) AP-700 User GuideParameter Tables176System ParametersInventory Management InformationNOTE: The inventory management comma

Command Line Interface (CLI) AP-700 User GuideParameter Tables177Network ParametersIP Configuration ParametersNOTE: The IP Address Assignment Type (ip

Command Line Interface (CLI) AP-700 User GuideParameter Tables178DHCP Server table for IP poolsNOTE: Set either End IP Address or Width (but not both)

Command Line Interface (CLI) AP-700 User GuideParameter Tables179SNTP ParametersLink Integrity ParametersLink Integrity IP Target TableName Type Value

Installation and Initialization AP-700 User GuidePrerequisites18Client IP Address Pool Allocation SchemeThe Access Point can automatically provide IP

Command Line Interface (CLI) AP-700 User GuideParameter Tables180Interface ParametersWireless Interface ParametersThe wireless interface group paramet

Command Line Interface (CLI) AP-700 User GuideParameter Tables181802.11a Only Parameters* Super mode must be enabled on the wireless interface before

Command Line Interface (CLI) AP-700 User GuideParameter Tables182802.11b Only Parameters802.11b/g Only ParametersName Type Value Access CLI ParameterO

Command Line Interface (CLI) AP-700 User GuideParameter Tables183* Also for 802.11g-wifi mode. 802.11g-wifi has been defined for Wi-Fi testing purpose

Command Line Interface (CLI) AP-700 User GuideParameter Tables184Channel Blacklist ParametersWireless Distribution System (WDS) ParametersWireless Int

Command Line Interface (CLI) AP-700 User GuideParameter Tables185Wireless Distribution System (WDS) Security Table ParametersThe WDS Security Table ma

Command Line Interface (CLI) AP-700 User GuideParameter Tables186Read/Write Password DisplayString User Definedpublic (default)6 - 32 charactersW snmp

Command Line Interface (CLI) AP-700 User GuideParameter Tables187HTTP Parameters* The help link must be set to an HTTP address. Use the forward slash

Command Line Interface (CLI) AP-700 User GuideParameter Tables188Serial Port ParametersRADIUS Based Management Access ParametersThe RADIUS Based Manag

Command Line Interface (CLI) AP-700 User GuideParameter Tables189Auto Configuration ParametersThese parameters relate to the Auto Configuration featur

Installation and Initialization AP-700 User GuideProduct Package19Product PackageEach AP-700 comes with the following:• AP-700 unit (with integrated 8

Command Line Interface (CLI) AP-700 User GuideParameter Tables190Filtering ParametersEthernet Protocol Filtering ParametersEthernet Filtering TableIde

Command Line Interface (CLI) AP-700 User GuideParameter Tables191Proxy ARP ParametersIP ARP Filtering ParametersBroadcast Filtering TableTCP/UDP Port

Command Line Interface (CLI) AP-700 User GuideParameter Tables192Alarms ParametersSNMP Table Host Table ParametersWhen creating table entries, you may

Command Line Interface (CLI) AP-700 User GuideParameter Tables193NOTE: When Heartbeat is enabled, the AP periodically sends a message to the Syslog se

Command Line Interface (CLI) AP-700 User GuideParameter Tables194Bridge ParametersSpanning Tree ParametersSpanning Tree Priority and Path Cost TableSt

Command Line Interface (CLI) AP-700 User GuideParameter Tables195Storm Threshold TableIntra BSS Subscriber BlockingThe following parameters control th

Command Line Interface (CLI) AP-700 User GuideParameter Tables196RADIUS ParametersGeneral RADIUS ParametersRADIUS Server Configuration ParametersNOTE:

Command Line Interface (CLI) AP-700 User GuideParameter Tables197Security ParametersMAC Access Control ParametersMAC Access Control TableRogue Scan Co

Command Line Interface (CLI) AP-700 User GuideParameter Tables198VLAN/SSID ParametersSecurity Profile TableThe Security Profile Table allows you to co

Command Line Interface (CLI) AP-700 User GuideParameter Tables199Other ParametersIAPP ParametersNOTE: These parameters configure the Inter Access Poin

AP-700 User Guide2Copyright© 2005 Proxim Corporation. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634; 5,875,179;

Installation and Initialization AP-700 User GuideHardware Installation20Hardware InstallationRequired Materials• AP-700 unit• Mounting bracket with sc

Command Line Interface (CLI) AP-700 User GuideParameter Tables200* QoS must be enabled on the wireless interface before spectralink can be enabled.† A

Command Line Interface (CLI) AP-700 User GuideCLI Batch File201QoS Enhanced Distributed Channel Access (EDCA) ParametersThe following commands configu

Command Line Interface (CLI) AP-700 User GuideCLI Batch File202executes the CLI commands. Commands that do not require a reboot take effect immediatel

Command Line Interface (CLI) AP-700 User GuideCLI Batch File203• Upload and reboot (this option is to be used for a CLI Batch file containing the conf

204AP-700 User GuideBASCII Character ChartYou can configure WEP Encryption Keys in either Hexadecimal or ASCII format. Hexadecimal digits are 0-9 and

205AP-700 User GuideCSpecifications• Software Features• Hardware Specifications• Available Channels• RF PerformanceSoftware FeaturesThe tables below l

Specifications AP-700 User GuideSoftware Features206Advanced Bridging FunctionsMedium Access Control (MAC) Functions * DFS is required for 802.11a APs

Specifications AP-700 User GuideSoftware Features207‡ Support is provided for a primary and backup RADIUS authentication server for both MAC-based aut

Specifications AP-700 User GuideHardware Specifications208Hardware SpecificationsPhysical SpecificationsDimensions (H x W x L) = 6.5 x 18.5 x 26 cm (2

Specifications AP-700 User GuideAvailable Channels209Available ChannelsAvailable channels vary based on operational mode and country. To verify which

Installation and Initialization AP-700 User GuideHardware Installation212. Attach one end of an Ethernet cable to the AP's LAN port (the center p

Specifications AP-700 User GuideRF Performance210RF PerformanceThe following tables show typical AP-700 RF performance values. 802.11a RF Performance*

211AP-700 User GuideDTechnical SupportIf you are having a problem using an AP and cannot resolve it with the information in Troubleshooting, gather th

Technical Support AP-700 User GuideTelephone Support212Submit a Knowledgebase question or open an issue at: <http://support.proxim.com/cgi-bin/prox

213AP-700 User GuideEStatement of WarrantyWarranty Coverage Proxim Corporation warrants that its Products are manufactured solely from new parts, conf

Statement of Warranty AP-700 User GuideOther Information214Calls to the Customer Service Center for reasons other than Product failure will not be acc

215AP-700 User GuideFRegulatory ComplianceNOTE: Please read this section before installing and using your product, and save these instructions. Visit

Regulatory Compliance AP-700 User GuideSafety Information (USA, Canada, & European Union)216Safety Information (USA, Canada, & European Union)

Regulatory Compliance AP-700 User GuideFederal Communications Commission (FCC)217Federal Communications Commission (FCC)

Regulatory Compliance AP-700 User GuideFederal Communications Commission (FCC)218WarningsThis equipment generates, uses, and can radiate radio frequen

Regulatory Compliance AP-700 User GuideIndustry Canada (IC)219Industry Canada (IC)

Installation and Initialization AP-700 User GuideHardware Installation22Figure 2-5 AP-700 Mounting PlateMounting the AP-700 to a Wall1. Put the mounti

Regulatory Compliance AP-700 User GuideEuropean Union220European Union NOTE: European Union includes the following countries: Austria, Belgium, Cyprus

Regulatory Compliance AP-700 User GuideRegulatory Compliance Certifications Summary221Regulatory Compliance Certifications Summary* European Union inc

Installation and Initialization AP-700 User GuideHardware Installation23Figure 2-6 Opening the Antenna Compartment2. There are two antenna connectors

Installation and Initialization AP-700 User GuideInitialization24InitializationThe following sections detail how to initialize the AP using ScanTool,

Installation and Initialization AP-700 User GuideInitialization25change your adapter setting at any time by clicking the Select Adapter button on the

Installation and Initialization AP-700 User GuideInitialization26d. Enter a static IP Address for the AP in the field provided. You must assign the un

Installation and Initialization AP-700 User GuideInitialization274. Enter the HTTP password in the Password field. Leave the User Name field blank. Fo

Installation and Initialization AP-700 User GuideInitialization28Figure 2-12 Setup WizardSetup Wizard Instructions1. Click Setup Wizard to begin. The

Installation and Initialization AP-700 User GuideInitialization29— 802.11g-wifi: 802.11g-wifi has been defined for Wi-Fi testing purporses. It is not

AP-700 User Guide3Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation and Initialization AP-700 User GuideInitialization30Download the Software1. In your web browser, go to http://support.proxim.com. 2. If p

Installation and Initialization AP-700 User GuideInitialization31Figure 2-14 Warning Message5. Click OK to continue with the operation or Cancel to ab

Installation and Initialization AP-700 User GuideRelated Topics32Install Updates from your TFTP Server using the CLI1. Download the latest software to

33AP-700 User Guide3System StatusThe first screen displayed after Logging In is the System Status screen. You can always return to this screen by clic

34AP-700 User Guide4Advanced ConfigurationThis chapter contains information on configuring settings in the following categories:• System: Configure sp

Advanced Configuration AP-700 User Guide35Figure 4-1 Configure Main Screen2. Click the tab that corresponds to the parameter you want to configure. Fo

Advanced Configuration AP-700 User GuideSystem36SystemYou can configure and view the following parameters within the System Configuration screen:• Nam

Advanced Configuration AP-700 User GuideSystem37Access Point System Naming ConventionThe Access Point's system name is used as its host name. In

Advanced Configuration AP-700 User GuideNetwork38NetworkThe Network tab contains the following sub-tabs:• IP Configuration• DHCP Server• DHCP Relay Ag

Advanced Configuration AP-700 User GuideNetwork39Basic IP Parameters• IP Address Assignment Type: Set this parameter to Dynamic to configure the Acces

Contents AP-700 User Guide4IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Advanced Configuration AP-700 User GuideNetwork40Figure 4-4 DHCP Server Configuration ScreenYou can configure and view the following parameters within

Advanced Configuration AP-700 User GuideNetwork41– Status: IP Pools are enabled upon entry in the table. You can also disable or delete entries by cha

Advanced Configuration AP-700 User GuideNetwork42Figure 4-6 DHCP Server IP Address Table - Edit EntriesTo add an entry, enter the IP Address of the DH

Advanced Configuration AP-700 User GuideNetwork43Figure 4-7 Link Integrity Configuration ScreenSNTP (Simple Network Time Protocol)SNTP allows a networ

Advanced Configuration AP-700 User GuideNetwork44Figure 4-8 SNTP Configuration ScreenYou can configure and view the following parameters within the SN

Advanced Configuration AP-700 User GuideNetwork45– Year: Enter the current year.– Month: Enter the month in digits (1-12).– Day: Enter the day in digi

Advanced Configuration AP-700 User GuideInterfaces46InterfacesFrom the Interfaces tab, you configure the Access Point’s operational mode settings, pow

Advanced Configuration AP-700 User GuideInterfaces47• 802.11g-wifi mode: The 802.11g-wifi mode has been defined for Wi-Fi testing purporses. It is not

Advanced Configuration AP-700 User GuideInterfaces483. Select the Country Code from the ISO/IEC 3166-1 CountryCode drop-down menu.4. Click OK.5. Confi

Advanced Configuration AP-700 User GuideInterfaces49Wireless (802.11a/b/g Radio)Figure 4-10 Wireless Interface

Contents AP-700 User Guide5Management VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Advanced Configuration AP-700 User GuideInterfaces50You can view and configure the following parameters for the Wireless interface:NOTE: You must rebo

Advanced Configuration AP-700 User GuideInterfaces51NOTE: Turbo mode is supported in 802.11a and 802.11g mode. If turbo mode is enabled, then this is

Advanced Configuration AP-700 User GuideInterfaces52RTS/CTS Medium ReservationThe 802.11 standard supports optional RTS/CTS communication based on pac

Advanced Configuration AP-700 User GuideInterfaces53Traps Generated During Wireless Service Shutdown (and Resume)The following traps are generated dur

Advanced Configuration AP-700 User GuideInterfaces54Figure 4-12 Channel Blacklist Table - Edit ScreenWireless Distribution System (WDS)A Wireless Dist

Advanced Configuration AP-700 User GuideInterfaces55• There are separate security settings for clients and WDS links. The same WDS link security mode

Advanced Configuration AP-700 User GuideInterfaces56Figure 4-15 Adding WDS Links6. Select whether to use encryption in the WDS by checking the Enable

Advanced Configuration AP-700 User GuideInterfaces57Figure 4-16 Ethernet Sub-tabFor best results, Proxim recommends that you configure the Ethernet se

Advanced Configuration AP-700 User GuideManagement58ManagementThe Management tab contains the following sub-tabs:• Passwords• IP Access Table• Service

Advanced Configuration AP-700 User GuideManagement59IP Access TableThe Management IP Access table limits in-band management access to the IP addresses

Contents AP-700 User Guide6Forced Reload Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Advanced Configuration AP-700 User GuideManagement60• Secure Management Status: Enables the further configuration of HTTPS Access, SNMPv3, and Secure

Advanced Configuration AP-700 User GuideManagement61Figure 4-17 Management Services Configuration Screen

Advanced Configuration AP-700 User GuideManagement62Telnet Configuration Settings• Telnet Interface Bitmask: Select the interface (Ethernet, Wireless,

Advanced Configuration AP-700 User GuideManagement63NOTE: When Secure Management is enabled on the AP, SSH will be enabled by default and cannot be di

Advanced Configuration AP-700 User GuideManagement64Serial Configuration SettingsThe serial port interface on the AP is enabled at all times. See Sett

Advanced Configuration AP-700 User GuideManagement65• RADIUS Profile for Management Access Control: Specifies the RADIUS Profile to be used for RADIUS

Advanced Configuration AP-700 User GuideManagement66Figure 4-19 Automatic Configuration ScreenSet up Automatic Configuration for Dynamic IPPerform the

Advanced Configuration AP-700 User GuideManagement67Figure 4-20 DHCP Options: Setting the Boot Server Host Name4. Add the Boot Server Hostname and Boo

Advanced Configuration AP-700 User GuideManagement68AP is not protected, an unauthorized person could reset the AP to factory defaults and thus gain c

Advanced Configuration AP-700 User GuideManagement692. Check (enable) or uncheck (disable) the Enable Hardware Configuration Reset checkbox.3. Change

Contents AP-700 User Guide7CLI Batch File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Advanced Configuration AP-700 User GuideFiltering70FilteringThe Access Point’s Packet Filtering features help control the amount of traffic exchanged

Advanced Configuration AP-700 User GuideFiltering71Each MAC Address or Mask is comprised of 12 hexadecimal digits (0-9, A-F) that correspond to a 48-b

Advanced Configuration AP-700 User GuideFiltering72• Wireless Client 2: 00:02:2D:51:32:12• Wireless Client 3: 00:20:A6:12:4E:38Prevent Two Specific De

Advanced Configuration AP-700 User GuideFiltering73• Wired MAC Address: 01:00:5E:00:32:4B• Wired Mask: FF:FF:FF:FF:FF:FF• Wireless MAC Address: 00:00:

Advanced Configuration AP-700 User GuideFiltering744. Set the destination Port Number (a value between 1 and 65535) to filter. See the IANA Web site a

Advanced Configuration AP-700 User GuideAlarms75AlarmsThe Alarms tab has the following sub-tabs:• Groups• Alarm Host Table• Syslog• Rogue ScanGroupsAl

Advanced Configuration AP-700 User GuideAlarms76Security Trap GroupWireless Interface/Card Trap GroupOperational Trap GroupTrap Name Description Sever

Advanced Configuration AP-700 User GuideAlarms77Flash Memory Trap GrouporiTrapDHCPFailed Response to the DHCP client request not received; device not

Advanced Configuration AP-700 User GuideAlarms78TFTP Trap GroupImage Trap GroupSNTP Trap Group In addition, the AP supports these standard traps, whic

Advanced Configuration AP-700 User GuideAlarms79NOTE: Up to 10 entries are possible in the Alarm Host table.• IP Address: Enter the Trap Host IP Addre

AP-700 User Guide8Caution: Exposure to Radio Frequency Radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Advanced Configuration AP-700 User GuideAlarms80SyslogThe Syslog messaging system enables the AP to transmit event messages to a central server for mo

Advanced Configuration AP-700 User GuideAlarms81• Syslog Lowest Priority Logged: The AP will send event messages to the Syslog server that correspond

Advanced Configuration AP-700 User GuideAlarms82Client Login Authentication Status6 Informational Client logs in/authenticates. Message includes:• Cli

Advanced Configuration AP-700 User GuideAlarms83Rogue ScanThe Rogue Scan feature provides an additional security level for wireless LAN deployments. R

Advanced Configuration AP-700 User GuideAlarms84The figure above shows Client 1 connected to a Trusted AP and Client 2 connected to a Rogue AP. The Tr

Advanced Configuration AP-700 User GuideAlarms85• Channel: the working channel of the detected station• SNR: the SNR value of the last frame from the

Advanced Configuration AP-700 User GuideAlarms86Figure 4-26 Rogue Scan Screen

Advanced Configuration AP-700 User GuideBridge87BridgeThe AP is a bridge between your wired and wireless networking devices. As a bridge, the function

Advanced Configuration AP-700 User GuideBridge88Figure 4-27 Spanning Tree Sub-TabStorm ThresholdStorm Threshold is an advanced Bridge setup option tha

Advanced Configuration AP-700 User GuideBridge89• Wireless Threshold: Enter the maximum allowed number of packets per second.Intra BSSThe wireless cli

9AP-700 User Guide1IntroductionThis chapter contains information on the following:• Document Conventions• Introduction to Wireless Networking• Guideli

Advanced Configuration AP-700 User GuideQoS90QoSWireless Multimedia Extensions (WME)/Quality of Service (QoS)The AP supports Wireless Multimedia Enhan

Advanced Configuration AP-700 User GuideQoS914. To add a QoS Policy, click the Add button in the “QoS Policies Table” box. The Add Entries box appears

Advanced Configuration AP-700 User GuideQoS92Priority MappingUse this page to configure QoS 802.1p to 802.1d priority mappings (for layer 2 policies)

Advanced Configuration AP-700 User GuideQoS93Figure 4-31 Add Priority Mapping Entry3. Select the 802.1p Priority (from 0-7) for 802.1d Priorities 0-7.

Advanced Configuration AP-700 User GuideQoS941. Click Configure > QoS > EDCA.Figure 4-32 EDCA Tables2. Click Edit and configure the following pa

Advanced Configuration AP-700 User GuideQoS95• Tx OP Limit: The Transmission Opportunity Limit. The Tx OP is an interval of time during which a partic

Advanced Configuration AP-700 User GuideRadius Profiles96Radius ProfilesConfiguring Radius Profiles on the AP allows the administrator to define a pro

Advanced Configuration AP-700 User GuideRadius Profiles97Figure 4-33 RADIUS Servers per VLANThis figure shows a network with separate authentication s

Advanced Configuration AP-700 User GuideRadius Profiles98Figure 4-34 RADIUS Server ProfilesAdding or Modifying a RADIUS Server ProfilePerform the foll

Advanced Configuration AP-700 User GuideRadius Profiles99Figure 4-35 Add RADIUS Server Profile• Server Profile Name: the profile name. This is the nam